Quantities explained: from one piece to repeat runs in Utah
How many parts you order changes how they are made. The metal is the same and the drawing is the same, but the way the shop sets up the work is not. This guide explains what changes as a part moves from a single prototype to repeat runs, so you know what to ask for and what to send at each step.
The four camps, one by one
Choose a camp to see what we ask for and how the work is set up at that quantity.
Camp 1 of 4 One piece, sometimes two or three versions
A single piece to hold in your hand
The first camp is one part made to see whether the idea works. Speed of learning matters more than speed of making, so we keep the setup simple and talk often.
What we need from you
- A sketch, a drawing or a model file, whichever exists
- What the part has to do and what it touches
- The material you have in mind, or the question of which one
- Anything you already know will change
What changes in the shop
- Parts are laid out and cut one at a time
- Holes, bends and pockets are set up by hand at the machine
- We call with questions instead of guessing
- Changes between versions are quick to make, so we expect them
Camp 2 of 4 A handful of pieces
First pieces for your approval
Once the shape is settled, we make the first few parts exactly as the drawing says and hand them over for your approval before anything else is cut.
What we need from you
- A drawing with the dimensions that matter marked
- The finish you expect on the edges and faces
- Who signs off on the first pieces at your end
- How the parts will be used or assembled
What changes in the shop
- We write down the order of operations for the part
- The first pieces are checked against the drawing with you
- Small fixes go back into the drawing, not into memory
- Material for the next step is planned once you approve
Camp 3 of 4 Dozens to a few hundred parts
A small batch that matches the first
With an approved part in hand, the job becomes about sameness. A simple jig or stop on the saw makes every part land where the first one did.
What we need from you
- The approved first piece or its revision on the drawing
- The quantity, and whether it can be split into lots
- How the parts should be packed and counted
- Any part markings you need
What changes in the shop
- Cutting is nested so sheets and bars are used well
- Stops, jigs and holding plates replace hand layout
- Deburring and edge work are done in one pass for the lot
- Parts are counted and packed the way you asked
Camp 4 of 4 Recurring orders, any size the shop can handle
Repeat runs when you need them again
The summit is a part you can order again by its name. The setup, the notes and the fixtures are kept, so a repeat run starts from what worked last time.
What we need from you
- The part name or number you use for it
- The quantity for this run
- Any revision since the last run
- Where the parts should be ready for pickup
What changes in the shop
- Saved setup notes and fixtures come off the shelf
- Material is ordered against the known cut list
- A first part from the run is compared to the approved sample
- Paperwork lists the revision so runs stay consistent
What changes from camp to camp
The same part, four ways of making it. Read across a row to see how one part of the job changes as the quantity grows.
| Aspect | Camp 1One-off | Camp 2First pieces | Camp 3Small batch | Camp 4Repeat runs |
|---|---|---|---|---|
| Layout | Marked by hand or straight from the file | Checked against the drawing with you | Nested on the sheet for the whole lot | Saved cut list and nest |
| Holding the part | Clamps and a vise | Clamps, with notes on how | Stops, jigs and holding plates | The same jigs, from the shelf |
| Your input | Lots of conversation | Approval of the first pieces | Quantity, packing and markings | Part name, revision and quantity |
| Changes | Expected and easy | Written into the drawing | Planned between lots | Treated as a new revision |
| Cost per part | Highest, setup is spread over one piece | Still high, setup over a few | Lower as setup is shared | Lowest, setup already exists |
Why one piece costs more per part
Most of the work in making a part happens before the first cut. Somebody reads the drawing, chooses the material, plans the order of operations, sets up the saw, the brake and the mill, and checks the first piece. For a single prototype, all of that time belongs to one part. For a batch of fifty, the same setup is shared by fifty parts.
That is why a quote for one piece and a quote for twenty pieces can look surprisingly close in total. It is also why it often pays to order two or three prototypes at once if you think you will need spares, or to tell us early that a small batch is likely to follow.
When to add a jig or fixture
A jig is a simple tool that holds a part or guides a drill so every part comes out the same. For a single piece it is rarely worth making one. For a small batch, a basic jig often pays for itself in saved layout time and fewer mistakes. For repeat runs, a good fixture is one of the most useful things a part can have, and we keep it on the shelf with your part number.
We suggest a jig when the numbers make sense and explain the choice in the quote. The jig stays in our shop for your repeat runs; ask if you would like it handed over with the parts.
Splitting a batch into lots
Sometimes you need a quantity over several months but not all at once. In that case we can cut the material for the whole quantity together, which keeps the material consistent and the nest efficient, and finish the parts in lots as you call them off. Tell us the total quantity and the size of each lot you expect, and we plan the job around it.

Common questions about quantities
Do you take very small orders?
One piece. Single prototypes are a normal part of our work.
What is the largest order you take?
It depends on the size of the part and the steps involved. Batches of a few hundred small parts are comfortable for our shop. Tell us the quantity and we will tell you honestly how we would plan it.
Can I start with a prototype and order a batch later?
Yes. That is the route most parts take. Your drawing, notes and any machining program stay in our files, so the batch starts from what was approved.
Do repeat runs need a new quote?
Repeat runs are quoted from the saved job, so the quote is quick to prepare. If the drawing has changed, we review the change before quoting.
Not sure which camp your part is at?
Tell us what you have and how many you think you will need. We will suggest where to start.